This branch instruction is a simple one, but always remember to fill the delay slot! If the 2 register parameters are not equal take the Branch else execute the instruction after the delay slot. Note: Delay Slot is always executed. This example is definitely longer but it's a very useful pattern for zero filling any memory range. A branch delay slot follows the instruction. Bgt s,t,addr pseudo branch if s t A branch delay slot follows the instruction. Ble s,t,addr pseudo branch if s branch delay slot follows the instruction. Blez s,addr normal branch if the two's comp. Integer in register s is branch delay slot follows the instruction.
Part 6: Jumps and Branches
The CPU will execute instructions in sequential order from top to bottom. This is good for simple programs but what if we want to do more than just add two numbers? For more complex programs, we may need loops or other conditions and these are accomplished through jumps and branches. Gambling ghost witcher 1 walkthrough.
What is a branch?
A branch is like walking and reaching a fork in the road. There are two paths from where you are standing and depending on which path you choose, you will go somewhere else.
When disassembling a program and viewing the graph mode, a typical representation of a branch may look like this:
The fork in the road is where the end of the first block occurs where there is a green arrow and a red arrow leading to separate blocks of code. The green path will be taken if the branch condition is true and the red path will be taken if the branch condition is false.
In this example, bnez $v0, 0x814, if $v0 does NOT contain the number 0, then the code will take the green path and otherwise take the red path.
Branch Delay Slot
Branching seems simple enough; however, in MIPS implementation it is a little bit more nuanced.
When the processor executes an instruction, the program counter is advanced during the Instruction Fetch (IF) stage.
Due to the pipeline structure where when a jump or branch is being executed and the instruction afterwards would also be put into the pipeline, MIPS implements something called the branch delay slot.
Control hazards occur because the $pc after a branch is not known until it is figured out if the branch should be taken or not.
Instead of throwing the next instruction away when taking the branch, the instruction that is directly below a branch or jump always runs whether the branch is taken or not. This is why the instruction position after a branch or jump is called the branch delay slot.
As mentioned before, $pc is modified by 4 after the instruction fetch stage; however, when the branch is taken, $pc is modified during the branch instruction's execution (EX) stage. This affects what is chosen to be the next instruction after the branch delay slot that will be brought into the pipeline.
For the following instructions:
If the branch is taken, lw $v0, -0x7fd0($gp) from address 0x814 will be put into the pipeline.
| $pc | Cycles | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 |
|---|---|---|---|---|---|---|---|---|---|---|
| 0x7e4 | lw $v0, 0x18($fp) | IF | ID | EX | ME | WB | ||||
| 0x7e8 | bnez $v0, 0x814 | IF | ID | EX | ME | WB | ||||
| 0x7ec | noop | IF | ID | EX | ME | WB | ||||
| 0x814 | lw $v0, -0x7fd0($gp) | IF | ID | EX | ME | WB | ||||
| 0x818 | addiu $a0, $v0, str.x_is_NOT_0 | IF | ID | EX | ME | WB |
If the branch is NOT taken, $pc has not been modified by the branch instruction's execution stage, so the instruction from address 0x7f0 will be in the pipeline:
| $pc | Cycles | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 |
|---|---|---|---|---|---|---|---|---|---|---|
| 0x7e4 | lw $v0, 0x18($fp) | IF | ID | EX | ME | WB | ||||
| 0x7e8 | bnez $v0, 0x814 | IF | ID | EX | ME | WB | ||||
| 0x7ec | noop | IF | ID | EX | ME | WB | ||||
| 0x7f0 | lw $v0, -0x7fd0($gp) | IF | ID | EX | ME | WB | ||||
| 0x7f4 | addiu $a0, $v0, str.x_is_0 | IF | ID | EX | ME | WB |
Note: When no work is to be performed upon branching, often a noop is placed in the branch delay slot.
So what is a jump?
Jumps and branches both modify the program counter ($pc) in order to change code flow of the program and both utilize the branch delay slot; however, they are different based on how they modify the program counter.
Branches are conditional and are used to provide logic to the program and make it do different things. Branches require several bits in the machine code instruction for the condition so they have less bits to use for the location of the branch. That's why branches use a specified offset from the current program counter and can't go as far as a jump.
Jumps are unconditional and have more bits to go to a specified 26-bit memory address.
In short, jumps can go to code that is a greater distance in memory using an absolute address whereas branches have a shorter range and are relative because they are conditional.
Further Reading
1. Branch Delay Slot Tricks
2. Delay Slot [ Wikipedia ]
2. Branch Prediction Schemes (IA State)
MIPS Delay Slot Instructions
On the MIPS architecture, jump and branch instructions have a 'delay slot'. This means that the instruction after the jump or branch instruction is executed before the jump or branch is executed.
In addition, there is a group of 'branch likely' conditional branch instructions in which the instruction in the delay slot is executed only if the branch is taken.
The MIPS processors execute the jump or branch instruction and the delay slot instruction as an indivisible unit. If an exception occurs as a result of executing the delay slot instruction, the branch or jump instruction is not executed, and the exception appears to have been caused by the jump or branch instruction. Sports gambling virginia.
This behavior of the MIPS processors affects both the TotalView instruction step command and TotalView breakpoints.
Mips Instruction Set Branch Delay Slot
The TotalView instruction step command will step both the jump or branch instruction and the delay slot instruction as if they were a single instruction.
Mips Branch Delay Slot Instructions
If a breakpoint is placed on a delay slot instruction, execution will stop at the jump or branch preceding the delay slot instruction, and TotalView will not know that it is at a breakpoint. At this point, attempting to continue the thread that hit the breakpoint without first removing the breakpoint will cause the thread to hit the breakpoint again without executing any instructions. Before continuing the thread, you must remove the breakpoint. If you need to reestablish the breakpoint, you might then use the instruction step command to execute just the delay slot instruction and the branch.
A breakpoint placed on a delay slot instruction of a branch likely instruction will be hit only if the branch is going to be taken.
